Forum Replies Created
-
hot mark how much is it per meter
looked at grafityp emailed them they say 4.92 a meter for 378mm wideis that about right seems dear to me -
onestopsigns
MemberMay 20, 2005 at 6:57 pm in reply to: can anyone tell me if the creation a630 is a good buy?may be but its an upgrade
and who would fix mine
the seller wont h e wont even return calls
creation wont i think as all i get when i try to enter contact page is sonme hi ro glifficks and microsoft 404 message -
onestopsigns
MemberMay 20, 2005 at 6:19 pm in reply to: can anyone tell me if the creation a630 is a good buy?thank you very much for that pal
emailing them now
u say sign wizard are the uk imports for kingcut
do u know of them are they reliable as in will i get the cutter if i pay him as he wont accept paypal only cash through post or in to his bank -
onestopsigns
MemberMay 20, 2005 at 5:50 pm in reply to: can anyone tell me if the creation a630 is a good buy?graphtec ? ok how much are we talking and were from
how ever i would expect [call me crazy if u like] letters in cappitals 5 inch high all to be 5 inch high wether rounded tops or straight the higher point on wat ever letter should be 5 inch
for example i did some 18 inch letters it did all well and in cappitals i was so chuffed it had done them put them up and it looked funny the 4 letter in to the end were gradually getting bigger the end result was 19.3 inch letter at end and 18 inch at start
i think thats a bit off
how ever i was watching it cut today and i think the right hand base roller is moving slightly quicker than left but any way thanks for ur advice and i will be getting something new or used this week end so any hints were to get would be greatly appreciated
but budget is limited to 900 loans are out of question im afraid -
onestopsigns
MemberMay 20, 2005 at 8:40 am in reply to: can anyone tell me if the creation a630 is a good buy?well wat would u sugest ?
-
onestopsigns
MemberMay 20, 2005 at 8:31 am in reply to: can anyone tell me if the creation a630 is a good buy?philk
it really is a good cheapish machine
if the after sales service was up to scratch then this would be a perfect alrounderim sure the errors im getting are either a fault to over use of machine or a fault in how im doing it
(mod-edit) admin@uksignboards.com
-
onestopsigns
MemberMay 20, 2005 at 7:52 am in reply to: can anyone tell me if the creation a630 is a good buy?hi its not a case of i cant get hold of him
i emailed 2 nights ago saying i wanted to buy a new machine he emails back with wat must be his standard message saying please fone
so yesterday morning i go out of my way to fone before i plod of to work
he gets a customer in so asks if he can fone back takes house and mobile number as said was of to work
asked how long he said 2 -3 hours and guess wat im still fricken waitingjust like when i say i have problem with machine he says ill fone back and does till he doesnt now an answer then he just gives up and doesnt fone
how ever i do like the machines easy to use when they work and apart from the long words cutting squint and say i cut a a 6 letter word at list the forth letter is bigger than the rest
but at least haveing dealt with him i know i will get my prchase were as the king cut guy i dont no
and with all ebay purchases im a bit cautious hence asking if any 1 new sign wizard uk -
onestopsigns
MemberMay 19, 2005 at 7:37 pm in reply to: can anyone tell me if the creation a630 is a good buy?i do but got it from allan flyn signs and ive got the pcut version not kingcut
but flyn doesnt seem to value people paying him money his aftercare is shit and he doesnt return fone calls when he says he will -
onestopsigns
MemberMay 19, 2005 at 7:31 pm in reply to: can anyone tell me if the creation a630 is a good buy?or a company called signwizarduk
-
k an n i can get u in morning if still required got it in shop
-
i got the recaro one from a post here in swap sections about logos here it is hope this helps
-
well ive scrapped that machine now and am looking for another this evening yet again the bloke i got it from hasnt foned me back as he said h e would due to he had a customer in when i foned this morning
limited budget narrows the feild though -
amnd also is there a supplier here thats up in aberdeen ish that i could go and see for vinyl and equipment as it seems most of u know suppliers local and chat to them every other day from what im reading on other posts
-
hi basically i have a 24 inch cutter and some sub stuff fo rmugs ect
no one does this stuff up here so a good market if i can get it right
i was going to buy pre printed vinyl but at 35 quid a meter seemed a bit dear concidering id get 2 xboxes done out of a meter and skins are avail on ebay for 5 quid upwardswat exactly would i have to buy to print on to vinyl in small lenghts then laminate if required
bearing in mine a very small budget
-
onestopsigns
MemberMay 18, 2005 at 7:31 am in reply to: where can i get window tint & what do i do with it?hi thanks found the tuturial will have to do some reading now cheers again for your time folks
-
yes thanks that will do nicely cheers
-
i take it that wasnt allowed?
-
thatll be the pics we borrowed from webs and ebay to show examples of what im talking about as i have done any vans yet , a net aquaintence made the site for me as he said i had sh@@ one
-
thanks
i really appreciate all the time you and the rest of this board have put in on this -
me again bet your all sick of me
today we cut and drew several more of these bloody dragons none worked so tried 2 other types one failed and 1 worked
the 1 worked was the same as the one weve been trying to do except its the inners as i call it this one is no use to us as has no lines holding it together just the blocks like u filled in the colour of the other dragon .if thast makes sence
how ever with this one working i really dont understand why the others dont
would a new or different type of cutter be any different
lj can u email me the flexisign image u mentioned to loadsofstikas@aol.com got to get this sorted by thursday got a car coming in for them
never thought they would be this hard to do
does any one have any other dragons that may work the customer might opt for them in stead
-
hi
its a creation pcut 610 24 inch cutter on well its a serial end at the computer and a parrelel end at cutter
serial settings will check but basically 8 months ago i just plugged in loaded software and started cutting never did owt with settingsall other work is ok except it drags the vinyl accross on big jobs now sorted thanks to robert and a set square .
-
off to try it now mate cheers
-
ok i must be doing some thing wrong
al these u say will cut fine end up not cutting in my shop
all i do is import the ai image to flexisign stretch it to size by dragging the edges then press cut button
it then goes to cutter and cuts then it just decides to add linesnow when import it i cant see any lines that shouldnt be there
so i just dont understand it i really dont -
thats a great tip cheers
-
simon c cheers but thats the one with 5 legs
ive done a few more attempts today turning out costly lol
ok first one cut head then front paw then went and drew a straightline down the vinyl
second 1 cut the entire body perfect except a line near tail cutting back through the top of the boidyslightly
then the cutting finneshed and it missed out the head all to getherthe first was dragon 3 that i did through flexisign
the second was dragon 3 wich i did through flexisign and welded it -
flexi cuts with our cutter
creation pcut is all i know there chinese i think
gonna use this flexi its not as daunting as i first thought cheersdragon 3 ive imported itto flexi and i came up with lines like it was cut in sections but i welded it and now there gone so hope it works will give it a go shortly
thanks for all your help and fingers crossed i wont need to trouble u again -
ive a creation p cut 610
useing corel draw artcut as the cutter andplaying with flexisign as a new cutter proggy -
just looking now mate cheers
-
i seem to have a line going through his eye to his foot
-
Also, I’d convert all beziers to arcs. Sometime enlarging a file that has beziers, will thro a spike in the graphic, resulting in a cut tine.
didnt follow that bit sorry were are bexxiers and how do u convert themas for pannelling sorted that last week so just got the one pannel now
-
thanks for that lj most appreciated and will have a look at flexi to see if i cant work out to fix it me self had the same problem with a football clubs badge not long ago
but i useally use artcut but the flexisign7.5 i used to day was simple yet i started on flexi 6 could not master it . i take it we alter the pic in corel not flexi ? -
hi before i continue can i just thanks for all the replies this one has driven me up the wall the customer wanted it for his car i told him sorry today and sold him some squigly design instead but i hate giveing up on this so can you bear with me
1, how do see the lines that shouldntbe there when i use corel 11 it looks fine even in wire cut
2, ive welded the image file in eps in my cutter program called artcut i even used flexisign 7.5 today that failed to
3, tidying up is there some sort of help file to get me started on this
4,ive took it in to corel and exported the image and the wire frame aseps then imported to artcut and flexisign
out of 7 cuts i got 1 at 80 cm long to work but when i tried to do it a second time it failed5, cokka wat did u use to cut it and how big also email addy is (mod-edit)
6,lj i didnt design it mate it was here in the swaps section a few weeks ago
7, simon c how do u remove a layer in corel ?
8,carrie wat is this rip thing seen somet about it when i was looking at printers but not heard it on cutters were do i get one and wat does it do
9,lj the eps i posted mate no ai
eps was welded yet then u say i have 5 sections not sure howu now this or wat it means really want to learn if ya have time to helpand i know these may seem simple questions but take it easy with me my brains a bit slower than most
-
and how do u see if they cuts through them ?
-
thanks you lot are the best most appreciated will give that 1 a try tommorrow morning
wat are the error with the tail ?out of the cuts ive done most failed at the tongue tail or front claw -
wat price for cutter?ash
-
hi i use frontpage and host it with nd hosting
my hosting for first site was 40 quid but my main site i only paid 23 quid incluiding a dot com
front page open a template and copy paste wat u need
simple as can be or though with out a template its looks very daunting and complicated
frontpage comes with office 2003 if ya aint got it im sure i can send ya a disk(mod-edit)
-
hi ti runs at speed 50 ill try slowing it down
it manages to cut most stuff
think ill get another machine as the warranty with this one seems a bit well only if the seller can be bothered type
could do wit a spare any way
thanks for all ur help -
my name is ian ,lynn.
ill see if i cant knock up a standif no ill buy one soon
as for me it could be me but pretty sure i line em em damn close to straight but may be not
why a 48 inch cutter cause we want to do car side graphics more than any thing else and just seems easier to get the bigger one as some of the folk have asked for wider than 600 cm saves joining as ive never tried joining but i bet its a bugger to do
4 meter cut just seemed ideal as it would get his hole words in 1 go
as for splitting up the words this is wat i did yesterday eventually
but the weird bit there supposed to be 18inch letters high and thay came out well i was doing the word kessock and the k was perfect then e was ok and s came out angled a bit then s was 1/4 inch bigger then rest cut perfect just a 1/4 inch biggerhow much do u charge for an 18 inch high letter?
-
hi its a creation pcut 610/630
its about 7 months old bought from flyn signs via ebayit was bought as a new machine instead of getting one of these little 12 inch stikas machineswill give it a good clean tommorrow see if that helps got me first big order to do and its dragged off the page so ruined 4 meters today and and an hours work
was going to upgrade to 1220 machine as soonas i can afford one
but its a bugger it wont stay straight
i dont have the stand but would it makethat much difference i have a rooller type thingat back for the vinyl roll and i use rolls of 5 meters up to 20 meters
-
the last month or so but before that i was just cutting small stickers so wouldnt hav eknown
-
thanks for that mate ,pretty sur eits not me but ya never no .
-
ive the square aprilla in eps and an aprilla raceing one if there any use ill stick em up for ya
-
onestopsigns
MemberApril 29, 2005 at 6:48 pm in reply to: Number plates/ Show plates and the policethanks to beckys roller were now offering show plates
hig h street shop ,no dvla licence [yet] can we do a plate with kermit the frog at one end and the blokes licene plate lettering on rest
were in scotland if that makes a difference
wat would we have to do to be allowed by who ever to make this plate? -
the 3 dragons are the one im talking about except they had 5 legs and a kind gentle man here posted one with 4 legs this is the one ive been useing
the fault was caused near its tail first time and tounge second time
today i cut it a metwer long with flexi sign 7.5 and it cut perfectly
yet in artcut it donti need this bigger 1.5 meters to 2 meters long so will play with flex sign tommorrow as ive never used it till today as like artcuts simplicity
as for memory handshakes ect
is this memory in plotter orin pc ? if pc more memory will help yes? -
but ok then why does this cut buetifully at 30 cm long yet wont at 1 meter long
sure the same mistakes would be on the smaller as is on the bigger one -
hi thanks for all responces will post it up tommorrow as i left it in shop in disgust lol
i am on windows xp
i am set as x on x off
it is an outline and it does show up as it should do
ive had a few of these a si poiste dbefore and was told to weld which sorted it but its not sorting this one lol
mr sticker sounds like ur veiws might be the right thing how would i solve it
its an ai image which i saved to pc from here in the swaps sections of the dragon made for me with 4 legs
then i impoted to corel 11 then exported to eps for me to import in to artcutis there any cutters that just cut from ai ? or is that un heard of .
-
onestopsigns
MemberApril 26, 2005 at 9:29 am in reply to: Number plates/ Show plates and the policeso scotish folk dont have to register to make legal plates is this rite ?was reading dvla and they seem to hint that i do
-
cheers peter and jill thanks played a bit more with you said last and think ive done it was trying all morning but was not manageing with ur help ive cracked it i think
the reds gone the image is straight so the panels shouldnt be affected
so should cut it out now cheers off to try it
-
IT IS IN PANNELS
IT WOULD APEAR IF I CAN STRAIGHTEN THE IMAGE THEN I CAN MAKE IT FIT
BUT ITS PROVEING A PAIN
IVE ATTACHED THE IMAGE HOPEFULLY
ITSA RED BACKGROUND AND WHITE DRAGON I WANT THE WHITE DRAGON NOT THE RED SQUARE
BUT GOES FROM BOTTOM LEFT TO TOP RIGHT DIAGONALLY IF IT WENT STRAIGHT IT WOULDNT BE A PROBLEM LOOKING TO CUT THIS AT A SIZE OF 55CM HIGH BY 180 CM LONG
CANT FIND THE ATTACH BIT LOLBUT HERES A LINK
https://www.uksignboards.com/viewtopic.p … ght=dragonNOW ITS THE MIDDLE ONE I WANT AS THE BOTTOM 1 DOESNT HAVE AS MUCH DETAIL
CAN ANY 1 HELP ME SORT THIS OUT PLEASE DOING MY HEAD IN LOL AND ITS PROB SOMET SIMPLE
[/img] -
artcut2002
will have a look for panel settings
cheers
-
onestopsigns
MemberApril 23, 2005 at 8:56 pm in reply to: where can i source screenprinting squeegie blade please?dewi giveing them away with graphics is a good idea is there a web site or fone number would nt mind a hundred or so me self for that purpose
-
sorted cheers guys
-
hi cant pm back yet but its on way ok sent today
-
onestopsigns
MemberApril 19, 2005 at 10:36 am in reply to: is there a corel draw cutting driver for a pcut630/610? -
onestopsigns
MemberApril 19, 2005 at 10:06 am in reply to: is there a corel draw cutting driver for a pcut630/610?i can send ya some programs if u wish email me
-
THINK IVE A FEW SHEETS AND A TIN OF SPRAY VARNISH LEFT IF U WOULD LIKE EM TO TRY IT OUT BEFORE BUYING FROM SUPPLIERS
EMAIL ADDY ILL SEND EM OVER LOADSOFSTIKAS@AOL.COM -
onestopsigns
MemberApril 19, 2005 at 8:21 am in reply to: is there a corel draw cutting driver for a pcut630/610?WELL WAT IT IS IS I USE ARTCUT 2000 LOVE IT BUT SEEMS TO BE FAILING MY NEEDS LATELY WAS DOING THE 3D GUIDE FROM HERE AND WHEN I EXPORT OR SAVE AS AND OPEN IN ARTCUT IT JUST SEES THE SHADOW NO REST OF THE WORD SO ONLY CUTS SHADOW YET I OPEN TH EFILE IN COREL AGAIN AND ALL IS THERE SO I THOUGHT IF I CUT STRAIGHT FROM COREL IT WILL CUT ALL.
-
i used waterslide decals on mugs ages ago inkjet printer them then coat in loads of spray varnesh then water them on then spray again on mug
time consuming and frankly shite and the fumes from the avarnesh last for ages
as for versa cam i cant commment sorry but if theres another way to do ur items id sugest u do water slides are not the thing for me
-
onestopsigns
MemberApril 18, 2005 at 12:49 pm in reply to: can any one help me with 3d effects in corel please?cheers paul will give it a go
my names ian by the way -
onestopsigns
MemberApril 17, 2005 at 7:18 pm in reply to: help with eps it cuts over it self 3 times?cheers will give it a go wat program shows u layers ?
-
onestopsigns
MemberApril 17, 2005 at 3:16 pm in reply to: help with eps it cuts over it self 3 times?hi cheers for the quick reply i use corel draw to take the ai file from disk well hard drive now and then export as eps then import to artcut 2000 that was bundled with my creation pcut
how do i change this file ?
-
onestopsigns
MemberApril 16, 2005 at 12:18 pm in reply to: sublimation on a mug i seem to get little dots ?cheers will have words with supplier
-
onestopsigns
MemberApril 14, 2005 at 8:14 am in reply to: Can anyone tell me anything about the creation cutters?i have the the creation pcut 610
and i think its great
had a rolland camm1
that cut were u positioned on paper but the creation cuts from were u satart the blade off so i find that more usefull as u can use any old little bit of vinyl
much easier to use comes bundled with artcut 2002 which i also find easy to useebay sell these pcuts for 800 bought mine a while ago mind and got a free buisness card cutter to
-
ur an angel cheers that will do nicely will use search function in future to sorry
-
cheers for that mate but not much use to me im afraid looks wrong to me for a car that welsh dragon
any others about -
rotech mate cheap and good c86 ideal a4 starter printer
got mine from printowners web site with mug press ect very good for getting u stuff and the support after is excellent they even foned me back when i had colour fade problems id hate to see there fone billi got cartridges to see how i got on but will get the bulk system next ebay has it for 40 quid then bottles of 150 ml ink for under 25 each
-
hi cant wait any longer which ever 1 of u kind guys is willing to send ill take
email me cheers -
onestopsigns
MemberApril 1, 2005 at 11:45 am in reply to: Anything else i might need for sub printing?yes its taped to mug first time and pressure and heat according to bloke we got stuff from 180 c and 3 mins
ink on paper well useingthe profile given the pic comes out faded but prints perfect
useing the no colour alterations setting it comes out nice vibrant colours but has smudges on as if theres to much ink on paper -
onestopsigns
MemberApril 1, 2005 at 9:58 am in reply to: Anything else i might need for sub printing?hi sorry to jump in again but budone do u no why im getting faded looking graphics on mugs ?
-
onestopsigns
MemberMarch 31, 2005 at 9:57 pm in reply to: Anything else i might need for sub printing?well ive just started mugs with the same printer im useing lyson sublimatoon paper heat tape mite be an idea to ,ull need profiles for ur ink and printer
software well corel drawor photo shop ect -
hi thanks fo rall the welcomes
carrie another name ?only mine ian why?
-
hi i just bought my mug press and inks ect from [my appologisies if your not allowed to post sites up here some forums dont like it if this is the case please removeand accept my apppologises]
http://www.printerowners.co.uk/
the bloke i foned first was very helpfull
sold me all i needed
how ever i would sugest u buy ur printer from another place for cheapness i got the c86 a4 printer for 70 quid local and added sublimation inks and saved 100 quid ishnot quite got the hang of things me self my images seem a bit faint
but as for were to buy would recomend them
and itsnext day delivery.
i spent 900 quid with em and all arrived safely so seem trustable to which in this day and age has tobe a bonushope that site helps ya .