[anthony lee]

AOOOOOOOOOOOOOWWWW(hot) (:) 😛 :lol1: 😎 😀 🙂 😮

IVE GOT IT WORKING!!!!!!!!!!!!!!!!!!
THANKS GUYS YOUVE BEEN GREAT

AAAAAOOOOOOOOOOOWWWWWWWWWWWWWW

NOT SURE WHAT IT WAS, BUT IT JUST CUT !!!!!

BACK IN BUSINESSSS!!!!!!!!!!!!!11

OK TIME TO GET RID OF MY STUDENT OVERDRAUGHT!!!!!!!!!!!!!!! (hot)

[anthony lee]

hey guys when you say check the cutter port speed is 9600, is done by going into device managers and looking at the port setting?

[anthony lee]

il give that a shot, dont really think they will provide me with much support especially that their offices are in china,, il try anyhow

thanks

[anthony lee]

hi there, thanks for the replies

ive actually emailed signwizard the supplier several times, i think to the point where they dont even email me back 🙄

as for sb forum, ive been there, i did everything they asked.. the last idea was to try a shorter usb cable in which i did and had no luck… after that they didnt know what to suggest.

can anyone confirm that in contropl panel > printers > i should have a pcut 630 displaying as one of my printers? cause at the moment there is nothing in my printers folder?

cheers jonny they will be massively be helpful!

ant

[anthony lee]

at the mo
im using signblazer demo but this should be fully functional with some screens at the start up asking me to register

my settings are from the other thread as follows

Bits Per Second: 9600
Parity: None
Stop Bits: 1
Flow Control: Hardware

Click Advanced, set as follows:

Com Port Number: Com2
USB Transfer Sizes: Receive = 4096, Transmit = 4096
Latency Times = 1MS
Minimum Read/Write Time Out = 0MS
Serial Enumerator = Ticked
Serial Printer = Ticked
Cancel If Power On = Ticked
Event On Surprise Removal = Ticked
Set RTS On Close = Ticked

Click OK and OK again.

Close Device Manager

4. Open what ever cutting software you wish to use and set it up as follows:

Cutter = Creation PCut CT630
Serial Port/Com Port = Com2
Com Port Speed = 9600
Flow Control = Hardware

5. Check the port speed on the cutter is set to 9600.

now ive got an email today from the previous owner who had only limited knowledge of the setup but he told me to go into control panel and printers, then add printer -then some how add the pcut (but everytime i try add the printer from the cd that came with the cutter, it says there are no setup files?) anyways he said after doing this set it as the default printer

hope this helps

really and honestly appreciate your replies

thanks

[anthony lee]

hey steve thanks for the tip il try find one and test it out

thanks

[anthony lee]

ive just been on http://pcut-cn.com/edownload/download.php

i cant really see any vista drivers, ive also tried signwizards usb driver without success

[anthony lee]

hi no i havent, i dont have access to an xp machine, however ive read a few people running the pcut 630 on the vista with success, so i must be doing something wrong?

[anthony lee]

hi is any1 able to help me, located in leicester – i am willing to pay money fr some to help me set this up on my vista pc.

regards

[anthony lee]

i bought it 2nd hand from ebay.. i think they bought it from signwizard, i shall drop them an email however i reckon they will be reluctant to help a 2nd buyer.

ant

[anthony lee]

hi guys, i went over to sbe forum, did what they asked, played with config settings.. still no luck….. hmmm looks like im gonna have to sell it 🙁

[anthony lee]

hi guys, ok ive made a little progress, ive done the test cut.. and it cut fine.. and ive installed it as when i plu it in – on device manager it comes up as usb serial convertor – com2

now when i have something to be cut in sbe, setup the cutter as shown below

then i press cut tile

then the cut master pops up with the job however nothing happens???
[img=http://img218.imageshack.us/img218/746/sbe4pd6.th.jpg]

any one any ideas?

thanks guys

[anthony lee]

ahhhhhhhhhhhh

i just moved the head out and now it boots up!!!

(hot)

thanks john life saver! im gonna try it later and see how i get on!!!

thanks a bunch guys!!

[anthony lee]

this is how the head looks[/list]

[anthony lee]

hi without the pcut connected it stays with black dots, o dear.. looks like im gonna have to get a refund.. such a hassle as delivery was a bomb!

any1 else confirm this before i send it back?

thanks
ant

[anthony lee]

hi no it stays with black dots,
i spoke to the previous owner just now and she said that when i press online, the menus should come up as long as it is connected to the pc/installed.. shes running off xp..

any1 with this cutter and vista?

thanks

[anthony lee]

thanks lynn,

hey dave do u watch UFC by any chance? u look similar to gabriel Gonzaga 😎 lol