Forum Replies Created

  • john lowe

    Member
    October 19, 2007 at 3:59 pm in reply to: fiat coupe Vector outline – anyone please

    blimey that was quick thanks pete nice one

  • john lowe

    Member
    September 5, 2007 at 5:45 pm in reply to: Roland Cammjet 500 / ECOSOL MAX ink / Colorchoice RIP Help

    Hi Mike
    Thanks for the reply but i should have said i have been trying to set up bi direct in service mode and there is no where near enough range and the return print is fuzzy to. Sorry i should have made it more clear plus i always change all my own parts and the reason for the new main board is the old forgot to unplug the machine , could it be the head carriage board, its a bit too deep for me.

    thanks again mike,

    Kind regards
    John Lowe

  • john lowe

    Member
    September 5, 2007 at 2:48 pm in reply to: Roland Cammjet 500 / ECOSOL MAX ink / Colorchoice RIP Help

    Hi Mike
    Thanks for the reply good info its a bit of a problem living in Spain, anyway i have the printer up and running now but i still have a fault when i use bidirectional printing, it only prints nice in one direction even when i make the adjustments it seems to far out to adjust the machine has a new main board could it be the linear decoder if so can i turn it upside down or something sorry about this but the engineers here don’t even seem to know as much as i do for instance he said it was impossible to run impossible in this machine and there is no such thing as a jet-solver.

    Regards
    John Lowe

  • john lowe

    Member
    September 1, 2007 at 4:14 pm in reply to: Roland Cammjet 500 / ECOSOL MAX ink / Colorchoice RIP Help

    hi i was wondering if you might have some info for me on my fj52 jetsolver i have been using lyson ecosol inks but have had nothing but trouble with drop out and drying up , i use epson 3000 heads and normal dampers
    so my questions are will any other heads work and is the ink at fault
    have you heard of triangle ink ? is that ok i could go on and on any help on this subject would be great

  • john lowe

    Member
    July 13, 2007 at 7:23 am in reply to: what are peoples thoughts on dingtec P-Cut and other Imports

    what kind of lead are you using if its parallel then you should be using lpt1 and if you are using serial lead you use com port hope that helps cheers

  • john lowe

    Member
    July 8, 2007 at 11:29 am in reply to: what are peoples thoughts on dingtec P-Cut and other Imports

    ok i have supplies for vinyl and foam board and policrill you are welcome to them but you must be fully legal before they will sell to you

  • john lowe

    Member
    July 8, 2007 at 9:24 am in reply to: what are peoples thoughts on dingtec P-Cut and other Imports

    also in alicante not to far from torrevieja were are you ?have you got your supplies worked out yet i have most of mine but i could do with some more 😮

  • john lowe

    Member
    July 8, 2007 at 8:18 am in reply to: what are peoples thoughts on dingtec P-Cut and other Imports

    hi steve have you sorted your cutter problem yet and which part of spain are you in.
    these machines like to use parallel leads best of all and you need to have the lpt1 port set up for it 🙄

  • john lowe

    Member
    July 8, 2007 at 7:30 am in reply to: Hello from Spain

    thanks nik lynn and harry it’s good to be here 😛

  • john lowe

    Member
    July 7, 2007 at 4:25 pm in reply to: Hello from Spain

    thank you marcella nice of you to make me feel welcome 😀

Report

Harassment or bullying behavior
Contains mature or sensitive content
Contains misleading or false information
Contains abusive or derogatory content
Contains spam, fake content or potential malware

Block Member?

Please confirm you want to block this member.

You will no longer be able to:

  • See blocked member's posts
  • Mention this member in posts
  • Invite this member to groups
  • Message this member
  • Add this member as a connection

Please note: This action will also remove this member from your connections and send a report to the site admin. Please allow a few minutes for this process to complete.

Report

You have already reported this .